This tutorial picks up where my midriff yoke tutorial leaves off: In the images you see here, I've already removed the lower portion of the bodice to form the yoke. The next step, before we actually create the surplice neckline, will be to combine and eliminate some of the darts in the bodice. So in this tutorial, I'll show you how to move a dart using the slash-and-spread method. Although I'm working on my brunch dress bodice here, the steps I'll describe apply to many other situations where you would move or combine darts.
Combining Two Darts into One
For a bodice of this style, it doesn't make much sense to have a bust dart, so we need to combine the bust dart with the waist-fitting dart. When we're done, the bodice front will have one single dart that accomplishes the same fitting as the two darts we started with.
First, cut through the center of the bust dart, cutting almost to but not through the bust point. Do the same for the waist dart. The bottom corner of the bodice piece will now be connected only by a tiny paper hinge at the bust point, and should be able to pivot freely. (If it doesn't, you need to cut further.)
Pivot the piece so that the edges of the bust dart meet at the side seam, and tape it closed, making sure your paper lies flat with no wrinkles or hitches.
The edges of your remaining dart will be slightly uneven, so trace straight lines from the bottom corners to the bust point to form new, straight dart legs. (As a rule of thumb, when a bodice has only one dart, it extends all the way to the bust point. When it has two darts, the points of those darts fall somewhere in the outer third of the bust circle.)
Moving a Dart
Although slopers have a shoulder dart on the bodice back, few garments do. So what do we do with the shoulder dart? Often, the solution is to move it to a place, like the neckline, where it will eventually be cut off. That's what I'll do here. But you can use this same basic technique to move any dart, for construction or design reasons.
Again, we'll be using the slash-and-spread method, which means we'll be pivoting a piece of our pattern around a tiny paper hinge. On the bodice front, you use the bust point as your pivot point, but there's no equally obvious point on the bodice back. So before we can slash and spread, we need to establish and mark the pivot point, 1 1/2 inches below the end of the shoulder dart.
Then, draw a line where you would like your new dart to form. In this situation, the location of the new dart doesn't much matter, since I'll eventually cut it off when I lower the back neckline. But if you're creating a design element, you'll want to put some thought into the placement and direction of your relocated dart.
This is the bodice back. (The CB is on the right side of the picture.) I've drawn a line down from the neckline edge, which will be my relocated dart, and I've connected that line to the pivot point I just established. I've also drawn a line connecting the original dart to the pivot point.
Next, cut along those lines, to but not through the pivot point, leaving a paper hinge as before. Pivot the loose section of your pattern to close the orignial dart, keeping the pattern flat. This will open a dart in the new location.
This is what the pattern should look like after closing the original shoulder dart. I've taped a piece of paper behind the pattern to stabilize it.
If you intended to use this dart, you would refine it now. But since this area of my pattern will just be cut away, I'm not going to the effort to do that here.
That's all for now on moving darts! In the next post, I'll show you how to create the surplice neckline and make adjustments to the armscye for a sleeveless bodice.
Wednesday, June 9, 2010
Saturday, June 5, 2010
A Much-Needed Face-Lift
Hope you all like the new look of Made By J! This blog has been in serious need of a style overhaul for some time: I just picked some random colors when I created it, and I never intended them to be permanent. I love the new background and template--it's much fresher and more fun.
But enough fiddling on the computer--it's time to get back to the sewing machine...
But enough fiddling on the computer--it's time to get back to the sewing machine...
Drafting: A Midriff Yoke
First, trace your bodice front and back onto a clean piece of paper. Then, decide how wide you want your yoke to be. You should definitely use the bust circle on your sloper as a reference point, but it's also a good idea to use a pattern or RTW dress you like as a comparison. Full disclosure: In my original design, I went with a 3-inch yoke, and it was terrible! The bodice was totally disproportionate, and gave me an awful, saggy-boob look. So I started again and made a 4-inch yoke, which was infinitely better. The moral of the story is: designs sometimes look different when you're wearing them than they did when you're drafting them, and if I had compared my design to a dress that I liked, I might have avoided this miss-step. I didn't take pictures of my drafting the second time around, so be aware that the pictures I'm using here are from the initial version.
Mark the width of your yoke on the front and back bodice. Measure up from the bottom (waistline) edge. Your line will be discontinuous across the waist-fitting dart.
Label the center front of your yoke, then cut your yoke pieces apart from the bodice and tape them together. If you made a hash mark across the line before you cut, you'll have a notch to line up you're pieces when you sew.
Now you have two pieces--a bodice front and a front yoke--both cut on the fold.
Do the same to the back:
Notice that the midriff yoke you've created here is contoured: in other words, it's not simply a straight strip of fabric. The result of this, in the end, is a better-fitted garment, since the yoke follows your particular curves.
That's it for the midriff yoke! In the next drafting post, I'll pick up where we left off here, and walk you though the steps of drafting a sleeveless surplice bodice.
Thursday, May 27, 2010
Offity-Off!
We're off on our vacation today, so no sewing for a couple of days. I won't have my Friday Frock done by Friday--I never got around to doing the buttonholes. Oh, well!
But I do have something to show for myself today. Late last night, when I finally got around to wrapping the wedding gift, I realized I didn't have any ribbon! The paper I used to wrap it was beautiful, but it needed something more. So here's what I came up with: I ripped a narrow strip of white poly charmeuse from my stash, and used that as ribbon. I think it's a neat, rustic-chic look--at least, that's what I'm telling myself.
Have a wonderful week!
But I do have something to show for myself today. Late last night, when I finally got around to wrapping the wedding gift, I realized I didn't have any ribbon! The paper I used to wrap it was beautiful, but it needed something more. So here's what I came up with: I ripped a narrow strip of white poly charmeuse from my stash, and used that as ribbon. I think it's a neat, rustic-chic look--at least, that's what I'm telling myself.
Have a wonderful week!
Saturday, May 22, 2010
Brunch Dress Finished
Here's the brunch dress, which I actually like even more than the WGD. It's simple and comfortable, and certainly more versatile than the fancier dress.
Here's my fabric layout, which ran diagonally the entire length of our living room! I bought enough fabric to cut the skirt on the bias, but I decided, for simplicity's sake, to cut it on the straight grain. Now, I kind of regret that decision, since the skirt blends in to the waistband more than I might like, and I think the bias-cut skirt would have given the whole thing a bit more drama. But as a trade-off, I have enough fabric left over to make another BurdaStyle Ute blouse, which is turning out to be a great wardrobe-builder, and I know the blue paisley will work well in my spring/summer wardrobe.
The dress itself is printed cotton (I can't remember now if it's voile or lawn), and I lined it with white pima cotton lawn. The lining fabric was definitely an extravagant purchase--it cost more than the fashion fabric! But it was really and truly what I wanted, and it feels so luxurious when you're wearing it! I decided to line, rather than underline, because I love the look and feel of a fully lined dress, and both fabrics were so light-weight, I didn't worry about bulkiness. I both lined and underlined the waistband, to give it extra stability, since the fashion fabric was so delicate, and I think that was a smart choice.
Initially, I had some trouble with the bust-fitting for this dress, but the changes I made to the pattern had exactly the desired effect: the waistband fits close to my body under the bust, giving the dress a flattering shape. I'm really pleased with the results, which you can sort of see here. (It's also just a nice picture!)
In these pictures, I've accessorized the dress as I probably will for Angela's wedding brunch, with metalic strappy heels (because everything looks better with 3-inch heels) and my beloved-but-underutilized, paisley-embossed Hobo clutch, which I carried the day of my own wedding. (My unhealthy obsession with Hobo bags is certainly the subject of another post!) But the dress also works well in my casual wardrobe, paired with my new navy wedges and my favorite summer jacket.
Seriously versatile dress, right? Want your own? Well, stay tuned, because over the next week or so, I'll be writing up a series of posts describing how to draft this dress from a personal sloper or basic dress pattern.
Here's my fabric layout, which ran diagonally the entire length of our living room! I bought enough fabric to cut the skirt on the bias, but I decided, for simplicity's sake, to cut it on the straight grain. Now, I kind of regret that decision, since the skirt blends in to the waistband more than I might like, and I think the bias-cut skirt would have given the whole thing a bit more drama. But as a trade-off, I have enough fabric left over to make another BurdaStyle Ute blouse, which is turning out to be a great wardrobe-builder, and I know the blue paisley will work well in my spring/summer wardrobe.
The dress itself is printed cotton (I can't remember now if it's voile or lawn), and I lined it with white pima cotton lawn. The lining fabric was definitely an extravagant purchase--it cost more than the fashion fabric! But it was really and truly what I wanted, and it feels so luxurious when you're wearing it! I decided to line, rather than underline, because I love the look and feel of a fully lined dress, and both fabrics were so light-weight, I didn't worry about bulkiness. I both lined and underlined the waistband, to give it extra stability, since the fashion fabric was so delicate, and I think that was a smart choice.
Initially, I had some trouble with the bust-fitting for this dress, but the changes I made to the pattern had exactly the desired effect: the waistband fits close to my body under the bust, giving the dress a flattering shape. I'm really pleased with the results, which you can sort of see here. (It's also just a nice picture!)
In these pictures, I've accessorized the dress as I probably will for Angela's wedding brunch, with metalic strappy heels (because everything looks better with 3-inch heels) and my beloved-but-underutilized, paisley-embossed Hobo clutch, which I carried the day of my own wedding. (My unhealthy obsession with Hobo bags is certainly the subject of another post!) But the dress also works well in my casual wardrobe, paired with my new navy wedges and my favorite summer jacket.
Seriously versatile dress, right? Want your own? Well, stay tuned, because over the next week or so, I'll be writing up a series of posts describing how to draft this dress from a personal sloper or basic dress pattern.
Friday, May 21, 2010
Draping vs. Flat-Pattern: A Meditation
Clearly, draping is sexier. I mean, come on, it's just cool. Draping a garment on a dress-form totally makes you look like a slick fashion designer. Beyond the coolness factor, it also seems that draping gives you more control over your design than flat-pattern drafting. Because you're manipulating the fabric on the form, you can evaluate things like balance and dart placement as you go, rather than waiting till you prove your pattern in muslin to see whether you like the results. That seems like a real advantage to me, especially with more complicated designs.
That said, draping seems just as inefficient as flat-pattern drafting: in both cases, you have to create a design, copy or transfer your finished pattern pieces to paper, then prove the pattern in muslin and make adjustments from there.
And it also seems to me that draping has some real disadvantages for the home sewer. First of all, the dress-form seems like a real limiting factor. A good one is expensive, not to mention difficult to store. And, unless you have a custom form created to match your specific body, the fit of your garment is always going to be an approximation. Depending on how wonky your own personal shape is, you might or might not be able to find a form that matched your dimensions well. And, having bought that form, god help you if you change size or shape appreciably any time in the next ten years or so!
So, I could be way of base here, but this is the impression I got: Draping is cool, but it's much more useful if you're doing Fashion Design, rather than sewing for yourself. If you're a Designer, you'll want the added control and flexibility that draping on a form will give you in creating your designs. And you'll probably also be creating prototypes, rather than garments designed to be worn by a particular person with his or her own unique shape (to my mind, runway models don't count). But if you're sewing for yourself, you'll probably be needing more pencil skirts than pleated evening gowns, and you'll want them to fit you impeccably. You also might find yourself unwilling to integrate an expensive, person-sized inanimate object into your already cramped apartment.
So at this point I'd say that, if you want to become a Fashion Designer, buy yourself a form and get draping! But if your goals are modest and your resources are limited, like mine are, flat-pattern drafting is way to go.
What do you think?
Sunday, May 16, 2010
Drafting: A Convertible Collar
Here are some instructions for drafting a convertible collar--I made this one to complete the pattern for my Friday Frock, a shirt-dress from Bernina that's missing the collar piece.
Just a quick reminder, for anyone who isn't a regular reader of this blog. I use Norma Hollen's book Pattern Making by the Flat Pattern Method as a reference for all of my drafting, and I want to credit her appropriately. If you're interested in drafting, her book is an excellent resource.
Here's the definition of a "convertible collar": Unlike a regular, or "full-roll" collar, a convertible collar is designed to lie nicely if the collar is left open, and not buttoned all the way to the top. To accommodate this, the neckline edge of the convertible collar is angled slightly, so it matches the curve of the shirt's neckline edge. Since women's collared shirts are rarely buttoned to the top, when we think about a "shirt collar," what we usually have in mind is a convertible collar.
To begin, we'll draft a full-roll collar, which is ridiculously easy. Then we'll modify it to create the convertible collar.
First, measure the neckline edge of your garment. (I'm holding my tape measure on it's side so it will go around the curve better and give me a more accurate measurement.) Here, I just used the Bernina pattern before I added the seam allowances. My neckline edge measured 7.5 inches. Really that's only half of the length, since the yoke piece is cut on the fold. But since the collar will also be cut on the fold, that's exactly what I want.
Then, draw a rectangle that is the length of your neckline edge measurement (here 7.5 inches) and 3 inches wide. Measure the distance between the Center Back and your shoulder seam, and mark it on your collar. To create the point of your collar, extend one of the long edges of that rectangle by about an inch (more or less, depending on the pointiness of your desired collar), and draw a diagonal line connecting it to the corner of the shorter edge. That's it! That's your full-roll collar. In this picture, the lower (shorter) edge is the neckline edge, where you attach the collar to the shirt, and the left side is the center back, cut on the fold.
Now, to make the convertible collar, we want to create a slight angle in the neckline edge of our collar. To do this, measure 3/4 inches up from the lower right-hand corner, along the diagonal edge of the collar. Then draw a line from this point to your shoulder seam mark. The lower edge of your collar should now be angled slightly upward. As a consequence, it will also be slightly longer, so you'll need to adjust it. To do so, measure your new, angled neckline edge, and mark your desired length (in this case, remember, it was 7.5 inches). Shorten your collar by re-drawing the diagonal edge, beginning from the point you just marked and running parallel to the original line.
So, here's what your finished convertible collar should look like:
Of course, you still need to add seam allowances. And remember, the collar piece we've drafted gets cut on the fold, and you need to cut two of them: an upper collar and an under-collar.
Just a quick reminder, for anyone who isn't a regular reader of this blog. I use Norma Hollen's book Pattern Making by the Flat Pattern Method as a reference for all of my drafting, and I want to credit her appropriately. If you're interested in drafting, her book is an excellent resource.
Here's the definition of a "convertible collar": Unlike a regular, or "full-roll" collar, a convertible collar is designed to lie nicely if the collar is left open, and not buttoned all the way to the top. To accommodate this, the neckline edge of the convertible collar is angled slightly, so it matches the curve of the shirt's neckline edge. Since women's collared shirts are rarely buttoned to the top, when we think about a "shirt collar," what we usually have in mind is a convertible collar.
To begin, we'll draft a full-roll collar, which is ridiculously easy. Then we'll modify it to create the convertible collar.
First, measure the neckline edge of your garment. (I'm holding my tape measure on it's side so it will go around the curve better and give me a more accurate measurement.) Here, I just used the Bernina pattern before I added the seam allowances. My neckline edge measured 7.5 inches. Really that's only half of the length, since the yoke piece is cut on the fold. But since the collar will also be cut on the fold, that's exactly what I want.
So, here's what your finished convertible collar should look like:
Of course, you still need to add seam allowances. And remember, the collar piece we've drafted gets cut on the fold, and you need to cut two of them: an upper collar and an under-collar.
Subscribe to:
Posts (Atom)